diff --git a/printer.cfg b/printer.cfg
index d0c760a..bb8a456 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -11,11 +11,11 @@ serial: /tmp/klipper_host_mcu
 canbus_uuid: a39755b6c75c
 
 [mcu printhead]
-canbus_uuid: 0ab26b4c87c4
+canbus_uuid: 6e5db542668c
 
 [printer]
 kinematics: corexy
-max_velocity: 500
+max_velocity: 1000
 max_accel: 20000
 max_z_velocity: 20
 max_z_accel: 350
@@ -38,7 +38,7 @@ dir_pin: PE5
 enable_pin: !PC14
 microsteps: 16
 rotation_distance: 40
-full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
+full_steps_per_rotation:400  #set to 400 for 0.9 degree stepper
 endstop_pin: ^PF4
 position_min: 0
 position_endstop: 346
@@ -63,7 +63,7 @@ enable_pin: !PE4
 microsteps: 16
 rotation_distance: 40
 endstop_pin: ^PF3
-full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
+full_steps_per_rotation:400  #set to 400 for 0.9 degree stepper
 position_min: 0
 position_endstop: 355
 position_max: 355
@@ -194,9 +194,9 @@ pid_kp = 23.189
 pid_ki = 1.562
 pid_kd = 86.089
 ##	Try to keep pressure_advance below 1.0
-#pressure_advance: 0.05
+pressure_advance: 0.05
 ##	Default is 0.040, leave stock
-#pressure_advance_smooth_time: 0.040
+pressure_advance_smooth_time: 0.040
 
 [tmc2209 extruder]
 uart_pin: printhead: PA15
@@ -268,7 +268,7 @@ pin: printhead: PB6
 x_offset: 0
 y_offset: 25.0
 #z_offset: 0
-speed: 10.0
+speed: 30.0
 samples: 3
 samples_result: median
 sample_retract_dist: 5.0
@@ -388,17 +388,17 @@ points:
 	50,275
 	300,275
 	300,25
-speed: 300
+speed: 500
 horizontal_move_z: 10
 retries: 10
 retry_tolerance: 0.01
 max_adjust: 15
 
 [bed_mesh]
-speed: 300
-horizontal_move_z: 10
-mesh_min: 10,10
-mesh_max: 340,340
+speed: 500
+horizontal_move_z: 5
+mesh_min: 30,50
+mesh_max: 320,340
 probe_count: 5,5
 
 #####################################################################
@@ -558,8 +558,27 @@ auto_cancel_variation: 0.1
 #*# shaper_freq_y = 59.0
 #*#
 #*# [probe]
-#*# z_offset = -1.875
+#*# z_offset = -1.655
 #*#
 #*# [extruder]
 #*#
 #*# [heater_bed]
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.053095, 0.170595, 0.133095, 0.143095, 0.065595
+#*# 	  0.053095, 0.080595, 0.115595, 0.108095, 0.088095
+#*# 	  0.000595, 0.068095, 0.050595, 0.145595, 0.043095
+#*# 	  0.025595, 0.058095, 0.140595, 0.060595, 0.063095
+#*# 	  0.148095, 0.185595, 0.223095, 0.175595, 0.203095
+#*# x_count = 5
+#*# y_count = 5
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = lagrange
+#*# tension = 0.2
+#*# min_x = 30.0
+#*# max_x = 320.0
+#*# min_y = 50.0
+#*# max_y = 340.0