commit c8e68b7cbba26de98b85a4e84839f8d35d2d1f37 Author: Siwat Sirichai Date: Fri Sep 22 00:03:58 2023 +0700 Create printer.cfg diff --git a/printer.cfg b/printer.cfg new file mode 100644 index 0000000..0347942 --- /dev/null +++ b/printer.cfg @@ -0,0 +1,329 @@ +[mcu] +## [X in MOTOR1] - B Motor +## [Y in MOTOR2] - A Motor +## [E in MOTOR8] - Extruder +serial: /dev/serial/by-id/YOU_DIDNT_CHANGE_ME_YET +restart_method: command + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 3000 #Max 4000 +max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V +max_z_accel: 350 +square_corner_velocity: 5.0 + +[temperature_sensor MCU] +sensor_type: temperature_mcu + +[temperature_sensor SoC] +sensor_type: temperature_host + +##################################################################### +# X/Y Stepper Settings +##################################################################### + +## X Stepper on Motor1(B Motor) +[stepper_x] +step_pin: PE6 +dir_pin: PE5 +enable_pin: !PC14 +microsteps: 16 +rotation_distance: 40 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +endstop_pin: ^PF4 +position_min: 0 +position_endstop: 350 +position_max: 350 +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Y Stepper on Motor2 (A Motor) +[stepper_y] +step_pin: PE2 +dir_pin: PE1 +enable_pin: !PE4 +microsteps: 16 +rotation_distance: 40 +endstop_pin: ^PF3 +full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper +position_min: 0 +position_endstop: 350 +position_max: 350 +homing_speed: 25 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +##################################################################### +# Z Stepper Settings +##################################################################### + +## Z0 Stepper - Front Left on MOTOR3_A +[stepper_z] +step_pin: PB8 +dir_pin: !PB7 +enable_pin: !PE0 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 +endstop_pin: ^PF2 +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +position_endstop: -2 +position_max: 340 +position_min: -5 +homing_speed: 8 +second_homing_speed: 3 +homing_retract_dist: 3 + +## Z1 Stepper - Rear Left on Motor5 +[stepper_z1] +step_pin: PG13 +dir_pin: PG12 +enable_pin: !PG15 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Z2 Stepper - Rear Right on Motor6 +[stepper_z2] +step_pin: PG9 +dir_pin: PD7 +enable_pin: !PG11 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +## Z3 Stepper - Front Right on Motor7 +[stepper_z3] +step_pin: PD4 +dir_pin: PD3 +enable_pin: !PD6 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 16 + +##################################################################### +# Extruder +##################################################################### + +[multi_pin hotend_heater] +pins: PA0, PA1 + +# E0 on Motor8, Temperature Sensor on Motor4 +[extruder] +step_pin: PC7 +dir_pin: PC8 +enable_pin: !PD2 +rotation_distance: 8 +gear_ratio: 1:1 +microsteps: 16 +full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +nozzle_diameter: 0.400 +filament_diameter: 1.75 +heater_pin: hotend_heater +sensor_type: MAX31865 +sensor_pin: PB5 +spi_software_mosi_pin: PG6 +spi_software_miso_pin: PG7 +spi_software_sclk_pin: PG8 +rtd_nominal_r: 1000 +rtd_reference_r: 430 +rtd_num_of_wires: 2 +rtd_use_50Hz_filter: True +min_temp: 10 +max_temp: 270 +max_power: 1.0 +min_extrude_temp: 170 +control = pid +pid_kp = 26.213 +pid_ki = 1.304 +pid_kd = 131.721 +## Try to keep pressure_advance below 1.0 +#pressure_advance: 0.05 +## Default is 0.040, leave stock +#pressure_advance_smooth_time: 0.040 + +[tmc2209 extruder] +uart_pin: PD5 +interpolate: false +run_current: 0.5 +stealthchop_threshold: 0 + +##################################################################### +# Bed Heater +##################################################################### + +## SSR Pin - HE2 +[heater_bed] +heater_pin: PA3 +sensor_type: "Generic 3950" +sensor_pin: PB1 +max_power: 1 +min_temp: 0 +max_temp: 120 +control: pid +pid_kp: 58.437 +pid_ki: 2.347 +pid_kd: 363.769 + +##################################################################### +# Probe +##################################################################### + +[probe] +## Inductive Probe +## This probe is not used for Z height, only Quad Gantry Leveling +## NPN and PNP proximity switch types can be set by jumper +pin: ^PF1 +x_offset: 0 +y_offset: 25.0 +z_offset: 0 +speed: 10.0 +samples: 3 +samples_result: median +sample_retract_dist: 5.0 +samples_tolerance: 0.006 +samples_tolerance_retries: 3 + +##################################################################### +# Fan Control +##################################################################### + +[fan] +## Print Cooling Fan - CNC_FAN0 +pin: PF7 +kick_start_time: 0.5 +## Depending on your fan, you may need to increase this value +## if your fan will not start. Can change cycle_time (increase) +## if your fan is not able to slow down effectively +off_below: 0.10 + +[heater_fan hotend_fan] +## Hotend Fan - CNC_FAN1 +pin: PF9 +max_power: 1.0 +kick_start_time: 0.5 +heater: extruder +heater_temp: 50.0 +fan_speed: 1.0 + +[heater_fan exhaust_fan] +# Exhaust fan - CNC_FAN3 +pin: PF6 +max_power: 1.0 +shutdown_speed: 0.0 +kick_start_time: 5.0 +heater: heater_bed +heater_temp: 60 +fan_speed: 1.0 + +[multi_pin controller_fans] +pins: PF8, PA4 + +[heater_fan controller_fan] +## Controller fan - CNC_FAN2 +pin: controller_fans +kick_start_time: 0.5 +heater: heater_bed +heater_temp: 45.0 + + +##################################################################### +# LED Control +##################################################################### + +[neopixel caselight] +# Chamber Lighting - HE2 Connector (Optional) +pin: PD15 +chain_count: 30 +color_order: GRB + +##################################################################### +# Homing and Gantry Adjustment Routines +##################################################################### + +[idle_timeout] +timeout: 1800 + +[safe_z_home] +## XY Location of the Z Endstop Switch +## Update -10,-10 to the XY coordinates of your endstop pin +## (such as 157,305) after going through Z Endstop Pin +## Location Definition step. +home_xy_position:170,170 +speed:100 +z_hop:10 + +[quad_gantry_level] +## Use QUAD_GANTRY_LEVEL to level a gantry. +## Min & Max gantry corners - measure from nozzle at MIN (0,0) and +## MAX (250, 250), (300,300), or (350,350) depending on your printer size +## to respective belt positions +gantry_corners: + -60,-10 + 410,420 +points: + 50,25 + 50,275 + 300,275 + 300,25 +speed: 100 +horizontal_move_z: 10 +retries: 5 +retry_tolerance: 0.0075 +max_adjust: 10 + +[board_pins] +aliases: + # EXP1 header + EXP1_1=PE9, EXP1_2=PE10, + EXP1_3=PE11, EXP1_4=PE12, + EXP1_5=PE13, EXP1_6=PE14, # Slot in the socket on this side + EXP1_7=PE15, EXP1_8=PB10, + EXP1_9=, EXP1_10=<5V>, + + # EXP2 header + EXP2_1=PB14, EXP2_2=PB13, + EXP2_3=PF7, EXP2_4=PB12, + EXP2_5=PE7, EXP2_6=PB11, # Slot in the socket on this side + EXP2_7=PE8, EXP2_8=, + EXP2_9=, EXP2_10=PC5 + +##################################################################### +# Macros +##################################################################### + +[gcode_macro G32] +gcode: + BED_MESH_CLEAR + G28 + QUAD_GANTRY_LEVEL + G28 + G0 X175 Y175 Z30 F3600 + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - please customise for your slicer of choice +gcode: + G32 ; home all axes + G1 Z20 F3000 ; move nozzle away from bed + + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-10.0 F3600 ; retract filament + G91 ; relative positioning + G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing + TURN_OFF_HEATERS + M107 ; turn off fan + G1 Z2 F3000 ; move nozzle up 2mm + G90 ; absolute positioning + G0 X125 Y250 F3600 ; park nozzle at rear + BED_MESH_CLEAR + \ No newline at end of file