Update printer.cfg
This commit is contained in:
parent
c9197d72d0
commit
c35948b4d6
775
printer.cfg
775
printer.cfg
|
|
@ -1,386 +1,389 @@
|
|||
[include mainsail.cfg]
|
||||
|
||||
# host MCU service is preinstalled and ready to use with:
|
||||
[mcu CB1]
|
||||
serial: /tmp/klipper_host_mcu
|
||||
|
||||
[mcu]
|
||||
canbus_uuid: a39755b6c75c
|
||||
|
||||
[mcu printhead]
|
||||
canbus_uuid: 0ab26b4c87c4
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 500
|
||||
max_accel: 4000 #Max 4000
|
||||
max_z_velocity: 20 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_z_accel: 350
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
[temperature_sensor MCU]
|
||||
sensor_type: temperature_mcu
|
||||
|
||||
[temperature_sensor SoC]
|
||||
sensor_type: temperature_host
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## X Stepper on Motor1(B Motor)
|
||||
[stepper_x]
|
||||
step_pin: PE6
|
||||
dir_pin: PE5
|
||||
enable_pin: !PC14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: ^PF4
|
||||
position_min: 0
|
||||
position_endstop: 346
|
||||
position_max: 346
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
[tmc5160 stepper_x]
|
||||
cs_pin: PC13
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
# Y Stepper on Motor2 (A Motor)
|
||||
[stepper_y]
|
||||
step_pin: PE2
|
||||
dir_pin: PE1
|
||||
enable_pin: !PE4
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PF3
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
position_min: 0
|
||||
position_endstop: 300
|
||||
position_max: 300
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
[tmc5160 stepper_y]
|
||||
cs_pin: PE3
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left on MOTOR3_A
|
||||
[stepper_z]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PE0
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
endstop_pin: ^PF2
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
position_endstop: -2
|
||||
position_max: 340
|
||||
position_min: -5
|
||||
homing_speed: 5
|
||||
second_homing_speed: 3
|
||||
homing_retract_dist: 3
|
||||
|
||||
[tmc5160 stepper_z]
|
||||
cs_pin: PB9
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.8
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left on Motor5
|
||||
[stepper_z1]
|
||||
step_pin: PG13
|
||||
dir_pin: !PG12
|
||||
enable_pin: !PG15
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
[tmc5160 stepper_z1]
|
||||
cs_pin: PG14
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right on Motor6
|
||||
[stepper_z2]
|
||||
step_pin: PG9
|
||||
dir_pin: PD7
|
||||
enable_pin: !PG11
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
[tmc5160 stepper_z2]
|
||||
cs_pin: PG10
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right on Motor7
|
||||
[stepper_z3]
|
||||
step_pin: PD4
|
||||
dir_pin: !PD3
|
||||
enable_pin: !PD6
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
[tmc5160 stepper_z3]
|
||||
cs_pin: PD5
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
[extruder]
|
||||
step_pin: printhead: PD0
|
||||
dir_pin: !printhead: PD1
|
||||
enable_pin: !printhead: PD2
|
||||
rotation_distance: 8
|
||||
gear_ratio: 1:1
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
heater_pin: printhead: PA2
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: printhead: PA4
|
||||
spi_bus: spi1a
|
||||
rtd_nominal_r: 1000
|
||||
rtd_reference_r: 430
|
||||
rtd_num_of_wires: 4
|
||||
min_temp: 10
|
||||
max_temp: 270
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
control = pid
|
||||
pid_kp = 26.213
|
||||
pid_ki = 1.304
|
||||
pid_kd = 131.721
|
||||
## Try to keep pressure_advance below 1.0
|
||||
#pressure_advance: 0.05
|
||||
## Default is 0.040, leave stock
|
||||
#pressure_advance_smooth_time: 0.040
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: printhead: PA15
|
||||
interpolate: false
|
||||
run_current: 0.47
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[adxl345]
|
||||
cs_pin: printhead: PB12
|
||||
spi_bus: spi2
|
||||
axes_map: x,y,z
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
## SSR Pin - HE2
|
||||
[heater_bed]
|
||||
heater_pin: PA3
|
||||
sensor_type: Generic 3950
|
||||
sensor_pin: PB1
|
||||
max_power: 1
|
||||
min_temp: 0
|
||||
max_temp: 120
|
||||
control: pid
|
||||
pid_kp: 58.437
|
||||
pid_ki: 2.347
|
||||
pid_kd: 363.769
|
||||
|
||||
#####################################################################
|
||||
# Probe
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
## Inductive Probe
|
||||
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||
## NPN and PNP proximity switch types can be set by jumper
|
||||
pin: ^PF1
|
||||
x_offset: 0
|
||||
y_offset: 25.0
|
||||
z_offset: 0
|
||||
speed: 10.0
|
||||
samples: 3
|
||||
samples_result: median
|
||||
sample_retract_dist: 5.0
|
||||
samples_tolerance: 0.006
|
||||
samples_tolerance_retries: 3
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
## Print Cooling Fan - CNC_FAN0
|
||||
pin: PA4
|
||||
kick_start_time: 0.5
|
||||
## Depending on your fan, you may need to increase this value
|
||||
## if your fan will not start. Can change cycle_time (increase)
|
||||
## if your fan is not able to slow down effectively
|
||||
off_below: 0.10
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
## Hotend Fan - CNC_FAN1
|
||||
pin: printhead: PA0
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_fan exhaust_fan]
|
||||
# Exhaust fan - CNC_FAN3
|
||||
pin: PF6
|
||||
max_power: 1.0
|
||||
shutdown_speed: 0.0
|
||||
kick_start_time: 5.0
|
||||
heater: heater_bed
|
||||
heater_temp: 60
|
||||
fan_speed: 1.0
|
||||
|
||||
[multi_pin controller_fans]
|
||||
pins: PF7,PF9
|
||||
|
||||
[heater_fan controller_fan]
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: multi_pin:controller_fans
|
||||
kick_start_time: 0.5
|
||||
heater: heater_bed
|
||||
heater_temp: 45.0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
[neopixel caselight]
|
||||
# Chamber Lighting - HE2 Connector (Optional)
|
||||
pin: PD15
|
||||
chain_count: 30
|
||||
color_order: GRB
|
||||
|
||||
[neopixel hotend_rgb]
|
||||
pin: printhead: PD3
|
||||
chain_count: 3
|
||||
color_order: GRB
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
|
||||
[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||
## (such as 157,305) after going through Z Endstop Pin
|
||||
## Location Definition step.
|
||||
home_xy_position:170,170
|
||||
speed:100
|
||||
z_hop:10
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||
## to respective belt positions
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
410,420
|
||||
points:
|
||||
50,25
|
||||
50,275
|
||||
300,275
|
||||
300,25
|
||||
speed: 100
|
||||
horizontal_move_z: 10
|
||||
retries: 5
|
||||
retry_tolerance: 0.0075
|
||||
max_adjust: 10
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE9, EXP1_2=PE10,
|
||||
EXP1_3=PE11, EXP1_4=PE12,
|
||||
EXP1_5=PE13, EXP1_6=PE14, # Slot in the socket on this side
|
||||
EXP1_7=PE15, EXP1_8=PB10,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PB14, EXP2_2=PB13,
|
||||
EXP2_3=PF7, EXP2_4=PB12,
|
||||
EXP2_5=PE7, EXP2_6=PB11, # Slot in the socket on this side
|
||||
EXP2_7=PE8, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=PC5
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
[gcode_macro G32]
|
||||
gcode:
|
||||
BED_MESH_CLEAR
|
||||
G28
|
||||
QUAD_GANTRY_LEVEL
|
||||
G28
|
||||
G0 X175 Y175 Z30 F3600
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||
gcode:
|
||||
G32 ; home all axes
|
||||
G1 Z20 F3000 ; move nozzle away from bed
|
||||
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-10.0 F3600 ; retract filament
|
||||
G91 ; relative positioning
|
||||
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||
TURN_OFF_HEATERS
|
||||
M107 ; turn off fan
|
||||
G1 Z2 F3000 ; move nozzle up 2mm
|
||||
G90 ; absolute positioning
|
||||
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||
BED_MESH_CLEAR
|
||||
|
||||
[include mainsail.cfg]
|
||||
|
||||
# host MCU service is preinstalled and ready to use with:
|
||||
[mcu CB1]
|
||||
serial: /tmp/klipper_host_mcu
|
||||
|
||||
[mcu]
|
||||
canbus_uuid: a39755b6c75c
|
||||
|
||||
[mcu printhead]
|
||||
canbus_uuid: 0ab26b4c87c4
|
||||
|
||||
[printer]
|
||||
kinematics: corexy
|
||||
max_velocity: 500
|
||||
max_accel: 4000 #Max 4000
|
||||
max_z_velocity: 20 #Max 15 for 12V TMC Drivers, can increase for 24V
|
||||
max_z_accel: 350
|
||||
square_corner_velocity: 5.0
|
||||
|
||||
[temperature_sensor MCU]
|
||||
sensor_type: temperature_mcu
|
||||
|
||||
[temperature_sensor SoC]
|
||||
sensor_type: temperature_host
|
||||
|
||||
#####################################################################
|
||||
# X/Y Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## X Stepper on Motor1(B Motor)
|
||||
[stepper_x]
|
||||
step_pin: PE6
|
||||
dir_pin: PE5
|
||||
enable_pin: !PC14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
endstop_pin: ^PF4
|
||||
position_min: 0
|
||||
position_endstop: 346
|
||||
position_max: 346
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
[tmc5160 stepper_x]
|
||||
cs_pin: PC13
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
# Y Stepper on Motor2 (A Motor)
|
||||
[stepper_y]
|
||||
step_pin: PE2
|
||||
dir_pin: PE1
|
||||
enable_pin: !PE4
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^PF3
|
||||
full_steps_per_rotation:200 #set to 400 for 0.9 degree stepper
|
||||
position_min: 0
|
||||
position_endstop: 300
|
||||
position_max: 300
|
||||
homing_speed: 25 #Max 100
|
||||
homing_retract_dist: 5
|
||||
homing_positive_dir: true
|
||||
|
||||
[tmc5160 stepper_y]
|
||||
cs_pin: PE3
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
## Z0 Stepper - Front Left on MOTOR3_A
|
||||
[stepper_z]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PE0
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
||||
## (+) value = endstop above Z0, (-) value = endstop below
|
||||
## Increasing position_endstop brings nozzle closer to the bed
|
||||
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
||||
#position_endstop: -2
|
||||
position_max: 340
|
||||
position_min: -5
|
||||
homing_speed: 5
|
||||
second_homing_speed: 3
|
||||
homing_retract_dist: 3
|
||||
|
||||
[tmc5160 stepper_z]
|
||||
cs_pin: PB9
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.8
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z1 Stepper - Rear Left on Motor5
|
||||
[stepper_z1]
|
||||
step_pin: PG13
|
||||
dir_pin: !PG12
|
||||
enable_pin: !PG15
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
[tmc5160 stepper_z1]
|
||||
cs_pin: PG14
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z2 Stepper - Rear Right on Motor6
|
||||
[stepper_z2]
|
||||
step_pin: PG9
|
||||
dir_pin: PD7
|
||||
enable_pin: !PG11
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
[tmc5160 stepper_z2]
|
||||
cs_pin: PG10
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
## Z3 Stepper - Front Right on Motor7
|
||||
[stepper_z3]
|
||||
step_pin: PD4
|
||||
dir_pin: !PD3
|
||||
enable_pin: !PD6
|
||||
rotation_distance: 40
|
||||
gear_ratio: 80:16
|
||||
microsteps: 16
|
||||
|
||||
[tmc5160 stepper_z3]
|
||||
cs_pin: PD5
|
||||
spi_software_mosi_pin: PG6
|
||||
spi_software_miso_pin: PG7
|
||||
spi_software_sclk_pin: PG8
|
||||
run_current: 0.800
|
||||
stealthchop_threshold: 0
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
[extruder]
|
||||
step_pin: printhead: PD0
|
||||
dir_pin: printhead: PD1
|
||||
enable_pin: !printhead: PD2
|
||||
rotation_distance: 8
|
||||
gear_ratio: 1:1
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
spi_speed: 4000000
|
||||
heater_pin: printhead: PB13
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: printhead: PA4
|
||||
spi_bus: spi1
|
||||
rtd_nominal_r: 1000
|
||||
rtd_reference_r: 4300
|
||||
rtd_num_of_wires: 4
|
||||
min_temp: 10
|
||||
max_temp: 270
|
||||
max_power: 0.7
|
||||
min_extrude_temp: 170
|
||||
control = pid
|
||||
pid_kp = 26.213
|
||||
pid_ki = 1.304
|
||||
pid_kd = 131.721
|
||||
## Try to keep pressure_advance below 1.0
|
||||
#pressure_advance: 0.05
|
||||
## Default is 0.040, leave stock
|
||||
#pressure_advance_smooth_time: 0.040
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: printhead: PA15
|
||||
interpolate: false
|
||||
run_current: 0.47
|
||||
stealthchop_threshold: 0
|
||||
|
||||
[adxl345]
|
||||
cs_pin: printhead: PB12
|
||||
spi_software_sclk_pin: printhead: PB10
|
||||
spi_software_mosi_pin: printhead: PB11
|
||||
spi_software_miso_pin: printhead: PB2
|
||||
axes_map: x,y,z
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
## SSR Pin - HE2
|
||||
[heater_bed]
|
||||
heater_pin: PA3
|
||||
sensor_type: Generic 3950
|
||||
sensor_pin: PB1
|
||||
max_power: 1
|
||||
min_temp: 0
|
||||
max_temp: 120
|
||||
control: pid
|
||||
pid_kp: 58.437
|
||||
pid_ki: 2.347
|
||||
pid_kd: 363.769
|
||||
|
||||
#####################################################################
|
||||
# Probe
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
## Inductive Probe
|
||||
## This probe is not used for Z height, only Quad Gantry Leveling
|
||||
## NPN and PNP proximity switch types can be set by jumper
|
||||
pin: printhead: PB6
|
||||
x_offset: 0
|
||||
y_offset: 25.0
|
||||
z_offset: 0
|
||||
speed: 10.0
|
||||
samples: 3
|
||||
samples_result: median
|
||||
sample_retract_dist: 5.0
|
||||
samples_tolerance: 0.006
|
||||
samples_tolerance_retries: 3
|
||||
|
||||
#####################################################################
|
||||
# Fan Control
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
## Print Cooling Fan - CNC_FAN0
|
||||
pin: PA4
|
||||
kick_start_time: 0.5
|
||||
## Depending on your fan, you may need to increase this value
|
||||
## if your fan will not start. Can change cycle_time (increase)
|
||||
## if your fan is not able to slow down effectively
|
||||
off_below: 0.10
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
## Hotend Fan - CNC_FAN1
|
||||
pin: printhead: PA0
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
fan_speed: 1.0
|
||||
|
||||
[heater_fan exhaust_fan]
|
||||
# Exhaust fan - CNC_FAN3
|
||||
pin: PF6
|
||||
max_power: 1.0
|
||||
shutdown_speed: 0.0
|
||||
kick_start_time: 5.0
|
||||
heater: heater_bed
|
||||
heater_temp: 60
|
||||
fan_speed: 1.0
|
||||
|
||||
[multi_pin controller_fans]
|
||||
pins: PF7,PF9
|
||||
|
||||
[heater_fan controller_fan]
|
||||
## Controller fan - CNC_FAN2
|
||||
pin: multi_pin:controller_fans
|
||||
kick_start_time: 0.5
|
||||
heater: heater_bed
|
||||
heater_temp: 45.0
|
||||
|
||||
|
||||
#####################################################################
|
||||
# LED Control
|
||||
#####################################################################
|
||||
|
||||
[neopixel caselight]
|
||||
# Chamber Lighting - HE2 Connector (Optional)
|
||||
pin: PD15
|
||||
chain_count: 30
|
||||
color_order: GRB
|
||||
|
||||
[neopixel hotend_rgb]
|
||||
pin: printhead: PD3
|
||||
chain_count: 3
|
||||
color_order: GRB
|
||||
|
||||
#####################################################################
|
||||
# Homing and Gantry Adjustment Routines
|
||||
#####################################################################
|
||||
|
||||
[idle_timeout]
|
||||
timeout: 1800
|
||||
|
||||
[safe_z_home]
|
||||
## XY Location of the Z Endstop Switch
|
||||
## Update -10,-10 to the XY coordinates of your endstop pin
|
||||
## (such as 157,305) after going through Z Endstop Pin
|
||||
## Location Definition step.
|
||||
home_xy_position:170,170
|
||||
speed:100
|
||||
z_hop:10
|
||||
|
||||
[quad_gantry_level]
|
||||
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
||||
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
||||
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
||||
## to respective belt positions
|
||||
gantry_corners:
|
||||
-60,-10
|
||||
410,420
|
||||
points:
|
||||
50,25
|
||||
50,275
|
||||
300,275
|
||||
300,25
|
||||
speed: 100
|
||||
horizontal_move_z: 10
|
||||
retries: 5
|
||||
retry_tolerance: 0.0075
|
||||
max_adjust: 10
|
||||
|
||||
[board_pins]
|
||||
aliases:
|
||||
# EXP1 header
|
||||
EXP1_1=PE9, EXP1_2=PE10,
|
||||
EXP1_3=PE11, EXP1_4=PE12,
|
||||
EXP1_5=PE13, EXP1_6=PE14, # Slot in the socket on this side
|
||||
EXP1_7=PE15, EXP1_8=PB10,
|
||||
EXP1_9=<GND>, EXP1_10=<5V>,
|
||||
|
||||
# EXP2 header
|
||||
EXP2_1=PB14, EXP2_2=PB13,
|
||||
EXP2_3=PF7, EXP2_4=PB12,
|
||||
EXP2_5=PE7, EXP2_6=PB11, # Slot in the socket on this side
|
||||
EXP2_7=PE8, EXP2_8=<RST>,
|
||||
EXP2_9=<GND>, EXP2_10=PC5
|
||||
|
||||
#####################################################################
|
||||
# Macros
|
||||
#####################################################################
|
||||
|
||||
[gcode_macro G32]
|
||||
gcode:
|
||||
BED_MESH_CLEAR
|
||||
G28
|
||||
QUAD_GANTRY_LEVEL
|
||||
G28
|
||||
G0 X175 Y175 Z30 F3600
|
||||
|
||||
[gcode_macro PRINT_START]
|
||||
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
||||
gcode:
|
||||
G32 ; home all axes
|
||||
G1 Z20 F3000 ; move nozzle away from bed
|
||||
|
||||
|
||||
[gcode_macro PRINT_END]
|
||||
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
||||
gcode:
|
||||
M400 ; wait for buffer to clear
|
||||
G92 E0 ; zero the extruder
|
||||
G1 E-10.0 F3600 ; retract filament
|
||||
G91 ; relative positioning
|
||||
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
||||
TURN_OFF_HEATERS
|
||||
M107 ; turn off fan
|
||||
G1 Z2 F3000 ; move nozzle up 2mm
|
||||
G90 ; absolute positioning
|
||||
G0 X125 Y250 F3600 ; park nozzle at rear
|
||||
BED_MESH_CLEAR
|
||||
|
||||
|
|
|
|||
Loading…
Reference in New Issue