From ab071904bdb0822efc3e58e523cacfabfcc3d82d Mon Sep 17 00:00:00 2001 From: Siwat Sirichai Date: Sat, 6 Jan 2024 13:25:37 +0700 Subject: [PATCH] Update printer.cfg --- printer.cfg | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/printer.cfg b/printer.cfg index 1f55f85..6e12de9 100644 --- a/printer.cfg +++ b/printer.cfg @@ -52,7 +52,7 @@ cs_pin: PC13 spi_software_mosi_pin: PG6 spi_software_miso_pin: PG7 spi_software_sclk_pin: PG8 -run_current: 1.000 +run_current: 1.414 stealthchop_threshold: 0 # Y Stepper on Motor2 (A Motor) @@ -76,7 +76,7 @@ cs_pin: PE3 spi_software_mosi_pin: PG6 spi_software_miso_pin: PG7 spi_software_sclk_pin: PG8 -run_current: 1.000 +run_current: 1.414 stealthchop_threshold: 0 @@ -109,7 +109,7 @@ cs_pin: PB9 spi_software_mosi_pin: PG6 spi_software_miso_pin: PG7 spi_software_sclk_pin: PG8 -run_current: 0.8 +run_current: 1 stealthchop_threshold: 0 ## Z1 Stepper - Rear Left on Motor5 @@ -126,7 +126,7 @@ cs_pin: PG14 spi_software_mosi_pin: PG6 spi_software_miso_pin: PG7 spi_software_sclk_pin: PG8 -run_current: 0.800 +run_current: 1 stealthchop_threshold: 0 ## Z2 Stepper - Rear Right on Motor6 @@ -143,7 +143,7 @@ cs_pin: PG10 spi_software_mosi_pin: PG6 spi_software_miso_pin: PG7 spi_software_sclk_pin: PG8 -run_current: 0.800 +run_current: 1 stealthchop_threshold: 0 ## Z3 Stepper - Front Right on Motor7 @@ -160,7 +160,7 @@ cs_pin: PD5 spi_software_mosi_pin: PG6 spi_software_miso_pin: PG7 spi_software_sclk_pin: PG8 -run_current: 0.800 +run_current: 1 stealthchop_threshold: 0 ##################################################################### @@ -532,18 +532,19 @@ feedrate_splice: 0.3 feedrate_normal: 1.0 auto_load_speed: 2 auto_cancel_variation: 0.1 + #*# <---------------------- SAVE_CONFIG ----------------------> #*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. #*# #*# [input_shaper] #*# shaper_type_x = mzv -#*# shaper_freq_x = 49.4 +#*# shaper_freq_x = 46.0 #*# shaper_type_y = zv -#*# shaper_freq_y = 62.0 +#*# shaper_freq_y = 59.0 #*# #*# [probe] #*# z_offset = -1.875 #*# #*# [extruder] #*# -#*# [heater_bed] \ No newline at end of file +#*# [heater_bed]