557 lines
23 KiB
C
557 lines
23 KiB
C
#ifndef CONFIGURATION_H
|
|
#define CONFIGURATION_H
|
|
|
|
#include "boards.h"
|
|
|
|
#define STR_HELPER(x) #x
|
|
#define STR(x) STR_HELPER(x)
|
|
|
|
//-//
|
|
#include <avr/pgmspace.h>
|
|
extern const uint16_t _nPrinterType;
|
|
extern const char _sPrinterName[] PROGMEM;
|
|
extern const uint16_t _nPrinterMmuType;
|
|
extern const char _sPrinterMmuName[] PROGMEM;
|
|
extern uint16_t nPrinterType;
|
|
extern PGM_P sPrinterName;
|
|
|
|
// Firmware version
|
|
#define FW_VERSION "3.8.1"
|
|
#define FW_COMMIT_NR 2869
|
|
// FW_VERSION_UNKNOWN means this is an unofficial build.
|
|
// The firmware should only be checked into github with this symbol.
|
|
#define FW_DEV_VERSION FW_VERSION_UNKNOWN
|
|
#define FW_REPOSITORY "Unknown"
|
|
#define FW_VERSION_FULL FW_VERSION "-" STR(FW_COMMIT_NR)
|
|
|
|
// G-code language level
|
|
#define GCODE_LEVEL 1
|
|
|
|
// Debug version has debugging enabled (the symbol DEBUG_BUILD is set).
|
|
// The debug build may be a bit slower than the non-debug build, therefore the debug build should
|
|
// not be shipped to a customer.
|
|
#define FW_VERSION_DEBUG 6
|
|
// This is a development build. A development build is either built from an unofficial git repository,
|
|
// or from an unofficial branch, or it does not have a label set. Only the build server should set this build type.
|
|
#define FW_VERSION_DEVEL 5
|
|
// This is an alpha release. Only the build server should set this build type.
|
|
#define FW_VERSION_ALPHA 4
|
|
// This is a beta release. Only the build server should set this build type.
|
|
#define FW_VERSION_BETA 3
|
|
// This is a release candidate build. Only the build server should set this build type.
|
|
#define FW_VERSION_RC 2
|
|
// This is a final release. Only the build server should set this build type.
|
|
#define FW_VERSION_GOLD 1
|
|
// This is an unofficial build. The firmware should only be checked into github with this symbol,
|
|
// the build server shall never produce builds with this build type.
|
|
#define FW_VERSION_UNKNOWN 0
|
|
|
|
#if FW_DEV_VERSION == FW_VERSION_DEBUG
|
|
#define DEBUG_BUILD
|
|
#else
|
|
#undef DEBUG_BUILD
|
|
#endif
|
|
|
|
#include "Configuration_prusa.h"
|
|
|
|
#define FW_PRUSA3D_MAGIC "PRUSA3DFW"
|
|
#define FW_PRUSA3D_MAGIC_LEN 10
|
|
|
|
#include "eeprom.h"
|
|
|
|
// This configuration file contains the basic settings.
|
|
// Advanced settings can be found in Configuration_adv.h
|
|
// BASIC SETTINGS: select your board type, temperature sensor type, axis scaling, and endstop configuration
|
|
|
|
// User-specified version info of this build to display in [Pronterface, etc] terminal window during
|
|
// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this
|
|
// build by the user have been successfully uploaded into firmware.
|
|
|
|
//#define STRING_VERSION "1.0.2"
|
|
|
|
#define STRING_VERSION_CONFIG_H __DATE__ " " __TIME__ // build date and time
|
|
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
|
|
|
|
// SERIAL_PORT selects which serial port should be used for communication with the host.
|
|
// This allows the connection of wireless adapters (for instance) to non-default port pins.
|
|
// Serial port 0 is still used by the Arduino bootloader regardless of this setting.
|
|
#define SERIAL_PORT 0
|
|
|
|
// This determines the communication speed of the printer
|
|
#define BAUDRATE 115200
|
|
|
|
// This enables the serial port associated to the Bluetooth interface
|
|
//#define BTENABLED // Enable BT interface on AT90USB devices
|
|
|
|
// The following define selects which electronics board you have.
|
|
// Please choose the name from boards.h that matches your setup
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines)
|
|
// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4)
|
|
// #define MACHINE_UUID "00000000-0000-0000-0000-000000000000"
|
|
|
|
// This defines the number of extruders
|
|
#define EXTRUDERS 1
|
|
|
|
//// The following define selects which power supply you have. Please choose the one that matches your setup
|
|
// 1 = ATX
|
|
// 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC)
|
|
|
|
#define POWER_SUPPLY 1
|
|
|
|
|
|
|
|
|
|
|
|
// Define this to have the electronics keep the power supply off on startup. If you don't know what this is leave it.
|
|
// #define PS_DEFAULT_OFF
|
|
|
|
|
|
// Actual temperature must be close to target for this long before M109 returns success
|
|
#define TEMP_RESIDENCY_TIME 3 // (seconds)
|
|
#define TEMP_HYSTERESIS 5 // (degC) range of +/- temperatures considered "close" to the target one
|
|
#define TEMP_WINDOW 1 // (degC) Window around target to start the residency timer x degC early.
|
|
|
|
|
|
|
|
// If your bed has low resistance e.g. .6 ohm and throws the fuse you can duty cycle it to reduce the
|
|
// average current. The value should be an integer and the heat bed will be turned on for 1 interval of
|
|
// HEATER_BED_DUTY_CYCLE_DIVIDER intervals.
|
|
//#define HEATER_BED_DUTY_CYCLE_DIVIDER 4
|
|
|
|
// If you want the M105 heater power reported in watts, define the BED_WATTS, and (shared for all extruders) EXTRUDER_WATTS
|
|
//#define EXTRUDER_WATTS (12.0*12.0/6.7) // P=I^2/R
|
|
//#define BED_WATTS (12.0*12.0/1.1) // P=I^2/R
|
|
|
|
// PID settings:
|
|
// Comment the following line to disable PID and enable bang-bang.
|
|
#define PIDTEMP
|
|
#define BANG_MAX 255 // limits current to nozzle while in bang-bang mode; 255=full current
|
|
#define PID_MAX BANG_MAX // limits current to nozzle while PID is active; 255=full current
|
|
#ifdef PIDTEMP
|
|
//#define PID_DEBUG // Sends debug data to the serial port.
|
|
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
|
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
|
#define PID_INTEGRAL_DRIVE_MAX PID_MAX //limit for the integral term
|
|
#define PID_K1 0.95 //smoothing factor within the PID
|
|
#define PID_dT ((OVERSAMPLENR * 10.0)/(F_CPU / 64.0 / 256.0)) //sampling period of the temperature routine
|
|
|
|
// If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
|
|
// Ultimaker
|
|
|
|
|
|
// MakerGear
|
|
// #define DEFAULT_Kp 7.0
|
|
// #define DEFAULT_Ki 0.1
|
|
// #define DEFAULT_Kd 12
|
|
|
|
// Mendel Parts V9 on 12V
|
|
// #define DEFAULT_Kp 63.0
|
|
// #define DEFAULT_Ki 2.25
|
|
// #define DEFAULT_Kd 440
|
|
#endif // PIDTEMP
|
|
|
|
|
|
//this prevents dangerous Extruder moves, i.e. if the temperature is under the limit
|
|
//can be software-disabled for whatever purposes by
|
|
#define PREVENT_DANGEROUS_EXTRUDE
|
|
//if PREVENT_DANGEROUS_EXTRUDE is on, you can still disable (uncomment) very long bits of extrusion separately.
|
|
#define PREVENT_LENGTHY_EXTRUDE
|
|
|
|
#ifdef DEBUG_DISABLE_PREVENT_EXTRUDER
|
|
#undef PREVENT_DANGEROUS_EXTRUDE
|
|
#undef PREVENT_LENGTHY_EXTRUDE
|
|
#endif //DEBUG_DISABLE_PREVENT_EXTRUDER
|
|
|
|
#define EXTRUDE_MAXLENGTH (X_MAX_LENGTH+Y_MAX_LENGTH) //prevent extrusion of very large distances.
|
|
|
|
/*================== Thermal Runaway Protection ==============================
|
|
This is a feature to protect your printer from burn up in flames if it has
|
|
a thermistor coming off place (this happened to a friend of mine recently and
|
|
motivated me writing this feature).
|
|
|
|
The issue: If a thermistor come off, it will read a lower temperature than actual.
|
|
The system will turn the heater on forever, burning up the filament and anything
|
|
else around.
|
|
|
|
After the temperature reaches the target for the first time, this feature will
|
|
start measuring for how long the current temperature stays below the target
|
|
minus _HYSTERESIS (set_temperature - THERMAL_RUNAWAY_PROTECTION_HYSTERESIS).
|
|
|
|
If it stays longer than _PERIOD, it means the thermistor temperature
|
|
cannot catch up with the target, so something *may be* wrong. Then, to be on the
|
|
safe side, the system will he halt.
|
|
|
|
Bear in mind the count down will just start AFTER the first time the
|
|
thermistor temperature is over the target, so you will have no problem if
|
|
your extruder heater takes 2 minutes to hit the target on heating.
|
|
|
|
*/
|
|
// If you want to enable this feature for all your extruder heaters,
|
|
// uncomment the 2 defines below:
|
|
|
|
// Parameters for all extruder heaters
|
|
//#define THERMAL_RUNAWAY_PROTECTION_PERIOD 40 //in seconds
|
|
//#define THERMAL_RUNAWAY_PROTECTION_HYSTERESIS 4 // in degree Celsius
|
|
|
|
// If you want to enable this feature for your bed heater,
|
|
// uncomment the 2 defines below:
|
|
|
|
// Parameters for the bed heater
|
|
//#define THERMAL_RUNAWAY_PROTECTION_BED_PERIOD 20 //in seconds
|
|
//#define THERMAL_RUNAWAY_PROTECTION_BED_HYSTERESIS 2 // in degree Celsius
|
|
//===========================================================================
|
|
|
|
|
|
//===========================================================================
|
|
//=============================Mechanical Settings===========================
|
|
//===========================================================================
|
|
|
|
// Uncomment the following line to enable CoreXY kinematics
|
|
// #define COREXY
|
|
|
|
// coarse Endstop Settings
|
|
#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors
|
|
|
|
#ifndef ENDSTOPPULLUPS
|
|
// fine endstop settings: Individual pullups. will be ignored if ENDSTOPPULLUPS is defined
|
|
// #define ENDSTOPPULLUP_XMAX
|
|
// #define ENDSTOPPULLUP_YMAX
|
|
// #define ENDSTOPPULLUP_ZMAX
|
|
// #define ENDSTOPPULLUP_XMIN
|
|
// #define ENDSTOPPULLUP_YMIN
|
|
// #define ENDSTOPPULLUP_ZMIN
|
|
#endif
|
|
|
|
#ifdef ENDSTOPPULLUPS
|
|
#define ENDSTOPPULLUP_XMAX
|
|
#define ENDSTOPPULLUP_YMAX
|
|
#define ENDSTOPPULLUP_ZMAX
|
|
#define ENDSTOPPULLUP_XMIN
|
|
#define ENDSTOPPULLUP_YMIN
|
|
#define ENDSTOPPULLUP_ZMIN
|
|
#endif
|
|
|
|
// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.
|
|
|
|
#define X_MAX_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
|
|
#define Y_MAX_ENDSTOP_INVERTING 0 // set to 1 to invert the logic of the endstop.
|
|
#define Z_MAX_ENDSTOP_INVERTING 1 // set to 1 to invert the logic of the endstop.
|
|
//#define DISABLE_MAX_ENDSTOPS
|
|
//#define DISABLE_MIN_ENDSTOPS
|
|
|
|
// Disable max endstops for compatibility with endstop checking routine
|
|
#if defined(COREXY) && !defined(DISABLE_MAX_ENDSTOPS)
|
|
#define DISABLE_MAX_ENDSTOPS
|
|
#endif
|
|
|
|
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
|
#define X_ENABLE_ON 0
|
|
#define Y_ENABLE_ON 0
|
|
#define Z_ENABLE_ON 0
|
|
#define E_ENABLE_ON 0 // For all extruders
|
|
|
|
// Disables axis when it's not being used.
|
|
#define DISABLE_X 0
|
|
#define DISABLE_Y 0
|
|
#define DISABLE_Z 0
|
|
#define DISABLE_E 0// For all extruders
|
|
#define DISABLE_INACTIVE_EXTRUDER 1 //disable only inactive extruders and keep active extruder enabled
|
|
|
|
|
|
// ENDSTOP SETTINGS:
|
|
// Sets direction of endstops when homing; 1=MAX, -1=MIN
|
|
#define X_HOME_DIR -1
|
|
#define Y_HOME_DIR -1
|
|
#define Z_HOME_DIR -1
|
|
|
|
#ifdef DEBUG_DISABLE_SWLIMITS
|
|
#define min_software_endstops 0
|
|
#define max_software_endstops 0
|
|
#else
|
|
#define min_software_endstops 1 // If true, axis won't move to coordinates less than HOME_POS.
|
|
#define max_software_endstops 1 // If true, axis won't move to coordinates greater than the defined lengths below.
|
|
#endif //DEBUG_DISABLE_SWLIMITS
|
|
|
|
|
|
#define X_MAX_LENGTH (X_MAX_POS - X_MIN_POS)
|
|
#define Y_MAX_LENGTH (Y_MAX_POS - Y_MIN_POS)
|
|
#define Z_MAX_LENGTH (Z_MAX_POS - Z_MIN_POS)
|
|
|
|
#define Z_HEIGHT_HIDE_LIVE_ADJUST_MENU 2.0f
|
|
|
|
#define HOME_Z_SEARCH_THRESHOLD 0.15f // Threshold of the Z height in calibration
|
|
|
|
//============================= Bed Auto Leveling ===========================
|
|
|
|
//#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
|
|
#define Z_PROBE_REPEATABILITY_TEST // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.
|
|
|
|
#ifdef ENABLE_AUTO_BED_LEVELING
|
|
|
|
// There are 2 different ways to pick the X and Y locations to probe:
|
|
|
|
// - "grid" mode
|
|
// Probe every point in a rectangular grid
|
|
// You must specify the rectangle, and the density of sample points
|
|
// This mode is preferred because there are more measurements.
|
|
// It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive
|
|
|
|
// - "3-point" mode
|
|
// Probe 3 arbitrary points on the bed (that aren't colinear)
|
|
// You must specify the X & Y coordinates of all 3 points
|
|
|
|
#define AUTO_BED_LEVELING_GRID
|
|
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
|
|
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
|
|
// and least squares solution is calculated
|
|
// Note: this feature occupies 10'206 byte
|
|
#ifdef AUTO_BED_LEVELING_GRID
|
|
|
|
// set the rectangle in which to probe
|
|
#define LEFT_PROBE_BED_POSITION 15
|
|
#define RIGHT_PROBE_BED_POSITION 170
|
|
#define BACK_PROBE_BED_POSITION 180
|
|
#define FRONT_PROBE_BED_POSITION 20
|
|
|
|
// set the number of grid points per dimension
|
|
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
|
|
#define AUTO_BED_LEVELING_GRID_POINTS 2
|
|
|
|
|
|
#else // not AUTO_BED_LEVELING_GRID
|
|
// with no grid, just probe 3 arbitrary points. A simple cross-product
|
|
// is used to esimate the plane of the print bed
|
|
|
|
#define ABL_PROBE_PT_1_X 15
|
|
#define ABL_PROBE_PT_1_Y 180
|
|
#define ABL_PROBE_PT_2_X 15
|
|
#define ABL_PROBE_PT_2_Y 20
|
|
#define ABL_PROBE_PT_3_X 170
|
|
#define ABL_PROBE_PT_3_Y 20
|
|
|
|
#endif // AUTO_BED_LEVELING_GRID
|
|
|
|
|
|
// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
|
|
// X and Y offsets must be integers
|
|
#define X_PROBE_OFFSET_FROM_EXTRUDER -25
|
|
#define Y_PROBE_OFFSET_FROM_EXTRUDER -29
|
|
#define Z_PROBE_OFFSET_FROM_EXTRUDER -12.35
|
|
|
|
#define Z_RAISE_BEFORE_HOMING 4 // (in mm) Raise Z before homing (G28) for Probe Clearance.
|
|
// Be sure you have this distance over your Z_MAX_POS in case
|
|
|
|
#define XY_TRAVEL_SPEED 8000 // X and Y axis travel speed between probes, in mm/min
|
|
|
|
#define Z_RAISE_BEFORE_PROBING 15 //How much the extruder will be raised before traveling to the first probing point.
|
|
#define Z_RAISE_BETWEEN_PROBINGS 5 //How much the extruder will be raised when traveling from between next probing points
|
|
|
|
//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
|
|
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.
|
|
|
|
//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
|
|
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
|
|
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.
|
|
|
|
// #define PROBE_SERVO_DEACTIVATION_DELAY 300
|
|
|
|
|
|
//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
|
|
//it is highly recommended you let this Z_SAFE_HOMING enabled!
|
|
|
|
//#define Z_SAFE_HOMING // This feature is meant to avoid Z homing with probe outside the bed area.
|
|
// When defined, it will:
|
|
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled
|
|
// - If stepper drivers timeout, it will need X and Y homing again before Z homing
|
|
// - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
|
|
// - Block Z homing only when the probe is outside bed area.
|
|
|
|
#ifdef Z_SAFE_HOMING
|
|
|
|
#define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2) // X point for Z homing when homing all axis (G28)
|
|
#define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2) // Y point for Z homing when homing all axis (G28)
|
|
|
|
#endif
|
|
|
|
#ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
|
|
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
|
|
#if (-(X_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
|
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
|
#endif
|
|
#else
|
|
#if ((X_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
|
|
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
|
#endif
|
|
#endif
|
|
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
|
|
#if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
|
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
|
#endif
|
|
#else
|
|
#if ((Y_PROBE_OFFSET_FROM_EXTRUDER * AUTO_BED_LEVELING_GRID_POINTS) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
|
|
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
|
|
#endif
|
|
#endif
|
|
|
|
|
|
#endif
|
|
|
|
#endif // ENABLE_AUTO_BED_LEVELING
|
|
|
|
|
|
// The position of the homing switches
|
|
//#define MANUAL_HOME_POSITIONS // If defined, MANUAL_*_HOME_POS below will be used
|
|
//#define BED_CENTER_AT_0_0 // If defined, the center of the bed is at (X=0, Y=0)
|
|
|
|
//Manual homing switch locations:
|
|
// For deltabots this means top and center of the Cartesian print volume.
|
|
|
|
|
|
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
|
|
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
|
|
// For the other hotends it is their distance from the extruder 0 hotend.
|
|
// #define EXTRUDER_OFFSET_X {0.0, 20.00} // (in mm) for each extruder, offset of the hotend on the X axis
|
|
// #define EXTRUDER_OFFSET_Y {0.0, 5.00} // (in mm) for each extruder, offset of the hotend on the Y axis
|
|
|
|
// The speed change that does not require acceleration (i.e. the software might assume it can be done instantaneously)
|
|
#define DEFAULT_XJERK 10 // (mm/sec)
|
|
#define DEFAULT_YJERK 10 // (mm/sec)
|
|
#define DEFAULT_ZJERK 0.4 // (mm/sec)
|
|
#define DEFAULT_EJERK 2.5 // (mm/sec)
|
|
|
|
//===========================================================================
|
|
//=============================Additional Features===========================
|
|
//===========================================================================
|
|
|
|
// Custom M code points
|
|
#define CUSTOM_M_CODES
|
|
#ifdef CUSTOM_M_CODES
|
|
#define CUSTOM_M_CODE_SET_Z_PROBE_OFFSET 851
|
|
#define Z_PROBE_OFFSET_RANGE_MIN -15
|
|
#define Z_PROBE_OFFSET_RANGE_MAX -5
|
|
#endif
|
|
|
|
|
|
// EEPROM
|
|
// The microcontroller can store settings in the EEPROM, e.g. max velocity...
|
|
// M500 - stores parameters in EEPROM
|
|
// M501 - reads parameters from EEPROM (if you need reset them after you changed them temporarily).
|
|
// M502 - reverts to the default "factory settings". You still need to store them in EEPROM afterwards if you want to.
|
|
//define this to enable EEPROM support
|
|
//#define EEPROM_SETTINGS
|
|
//to disable EEPROM Serial responses and decrease program space by ~1700 byte: comment this out:
|
|
// please keep turned on if you can.
|
|
//#define EEPROM_CHITCHAT
|
|
|
|
// Host Keepalive
|
|
//
|
|
// When enabled Marlin will send a busy status message to the host
|
|
// every couple of seconds when it can't accept commands.
|
|
//
|
|
#ifndef HEATBED_ANALYSIS
|
|
#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages
|
|
#endif //HEATBED_ANALYSIS
|
|
#define HOST_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113.
|
|
|
|
//LCD and SD support
|
|
#define SDSUPPORT // Enable SD Card Support in Hardware Console
|
|
//#define SDSLOW // Use slower SD transfer mode (not normally needed - uncomment if you're getting volume init error)
|
|
#define SD_CHECK_AND_RETRY // Use CRC checks and retries on the SD communication
|
|
#define ENCODER_PULSES_PER_STEP 4 // Increase if you have a high resolution encoder
|
|
//#define ENCODER_STEPS_PER_MENU_ITEM 1 // Set according to ENCODER_PULSES_PER_STEP or your liking
|
|
|
|
// The RepRapDiscount Smart Controller (white PCB)
|
|
// http://reprap.org/wiki/RepRapDiscount_Smart_Controller
|
|
#define REPRAP_DISCOUNT_SMART_CONTROLLER
|
|
#define SDSUPPORT
|
|
#define LCD_WIDTH 20
|
|
#define LCD_HEIGHT 4
|
|
|
|
|
|
// Increase the FAN pwm frequency. Removes the PWM noise but increases heating in the FET/Arduino
|
|
//#define FAST_PWM_FAN
|
|
|
|
// Temperature status LEDs that display the hotend and bet temperature.
|
|
// If all hotends and bed temperature and temperature setpoint are < 54C then the BLUE led is on.
|
|
// Otherwise the RED led is on. There is 1C hysteresis.
|
|
//#define TEMP_STAT_LEDS
|
|
|
|
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
|
|
// which is not ass annoying as with the hardware PWM. On the other hand, if this frequency
|
|
// is too low, you should also increment SOFT_PWM_SCALE.
|
|
#define FAN_SOFT_PWM
|
|
#define FAN_SOFT_PWM_BITS 4 //PWM bit resolution = 4bits, freq = 62.5Hz
|
|
|
|
// Bed soft pwm
|
|
#define HEATER_BED_SOFT_PWM_BITS 5 //PWM bit resolution = 5bits, freq = 31.25Hz
|
|
|
|
// Incrementing this by 1 will double the software PWM frequency,
|
|
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
|
|
// However, control resolution will be halved for each increment;
|
|
// at zero value, there are 128 effective control positions.
|
|
#define SOFT_PWM_SCALE 0
|
|
|
|
// M240 Triggers a camera by emulating a Canon RC-1 Remote
|
|
// Data from: http://www.doc-diy.net/photo/rc-1_hacked/
|
|
// #define PHOTOGRAPH_PIN 23
|
|
|
|
// SF send wrong arc g-codes when using Arc Point as fillet procedure
|
|
//#define SF_ARC_FIX
|
|
|
|
//define BlinkM/CyzRgb Support
|
|
//#define BLINKM
|
|
|
|
/*********************************************************************\
|
|
* R/C SERVO support
|
|
* Sponsored by TrinityLabs, Reworked by codexmas
|
|
**********************************************************************/
|
|
|
|
// Number of servos
|
|
//
|
|
// If you select a configuration below, this will receive a default value and does not need to be set manually
|
|
// set it manually if you have more servos than extruders and wish to manually control some
|
|
// leaving it undefined or defining as 0 will disable the servo subsystem
|
|
// If unsure, leave commented / disabled
|
|
//
|
|
//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command
|
|
|
|
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 //Enter the diameter (in mm) of the filament generally used (3.0 mm or 1.75 mm). Used by the volumetric extrusion.
|
|
|
|
// Calibration status of the machine, to be stored into the EEPROM,
|
|
// (unsigned char*)EEPROM_CALIBRATION_STATUS
|
|
enum CalibrationStatus
|
|
{
|
|
// Freshly assembled, needs to peform a self-test and the XYZ calibration.
|
|
CALIBRATION_STATUS_ASSEMBLED = 255,
|
|
|
|
// For the wizard: self test has been performed, now the XYZ calibration is needed.
|
|
CALIBRATION_STATUS_XYZ_CALIBRATION = 250,
|
|
|
|
// For the wizard: factory assembled, needs to run Z calibration.
|
|
CALIBRATION_STATUS_Z_CALIBRATION = 240,
|
|
|
|
// The XYZ calibration has been performed, now it remains to run the V2Calibration.gcode.
|
|
CALIBRATION_STATUS_LIVE_ADJUST = 230,
|
|
|
|
// Calibrated, ready to print.
|
|
CALIBRATION_STATUS_CALIBRATED = 1,
|
|
|
|
// Legacy: resetted by issuing a G86 G-code.
|
|
// This value can only be expected after an upgrade from the initial MK2 firmware releases.
|
|
// Currently the G86 sets the calibration status to
|
|
CALIBRATION_STATUS_UNKNOWN = 0,
|
|
};
|
|
|
|
#include "Configuration_adv.h"
|
|
#include "thermistortables.h"
|
|
|
|
|
|
#endif //__CONFIGURATION_H
|