113 lines
3.5 KiB
C
113 lines
3.5 KiB
C
/*
|
|
stepper.h - stepper motor driver: executes motion plans of planner.c using the stepper motors
|
|
Part of Grbl
|
|
|
|
Copyright (c) 2009-2011 Simen Svale Skogsrud
|
|
|
|
Grbl is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
Grbl is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#ifndef stepper_h
|
|
#define stepper_h
|
|
|
|
#include "planner.h"
|
|
|
|
#define ENABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 |= (1<<OCIE1A)
|
|
#define DISABLE_STEPPER_DRIVER_INTERRUPT() TIMSK1 &= ~(1<<OCIE1A)
|
|
|
|
#ifdef ABORT_ON_ENDSTOP_HIT_FEATURE_ENABLED
|
|
extern bool abort_on_endstop_hit;
|
|
#endif
|
|
|
|
// Initialize and start the stepper motor subsystem
|
|
void st_init();
|
|
|
|
// Interrupt Service Routines
|
|
|
|
void isr();
|
|
|
|
#ifdef LIN_ADVANCE
|
|
void advance_isr();
|
|
void advance_isr_scheduler();
|
|
void clear_current_adv_vars(); //Used to reset the built up pretension and remaining esteps on filament change.
|
|
#endif
|
|
|
|
// Block until all buffered steps are executed
|
|
void st_synchronize();
|
|
|
|
// Set current position in steps
|
|
void st_set_position(const long &x, const long &y, const long &z, const long &e);
|
|
void st_set_e_position(const long &e);
|
|
|
|
// Get current position in steps
|
|
long st_get_position(uint8_t axis);
|
|
|
|
// Get current x and y position in steps
|
|
void st_get_position_xy(long &x, long &y);
|
|
|
|
// Get current position in mm
|
|
float st_get_position_mm(uint8_t axis);
|
|
|
|
|
|
// Call this function just before re-enabling the stepper driver interrupt and the global interrupts
|
|
// to avoid a stepper timer overflow.
|
|
FORCE_INLINE void st_reset_timer()
|
|
{
|
|
// Clear a possible pending interrupt on OCR1A overflow.
|
|
TIFR1 |= 1 << OCF1A;
|
|
// Reset the counter.
|
|
TCNT1 = 0;
|
|
// Wake up after 1ms from now.
|
|
OCR1A = 2000;
|
|
}
|
|
|
|
void checkHitEndstops(); //call from somewhere to create an serial error message with the locations the endstops where hit, in case they were triggered
|
|
bool endstops_hit_on_purpose(); //avoid creation of the message, i.e. after homing and before a routine call of checkHitEndstops();
|
|
bool endstop_z_hit_on_purpose();
|
|
|
|
|
|
bool enable_endstops(bool check); // Enable/disable endstop checking. Return the old value.
|
|
bool enable_z_endstop(bool check);
|
|
void invert_z_endstop(bool endstop_invert);
|
|
|
|
void checkStepperErrors(); //Print errors detected by the stepper
|
|
|
|
void finishAndDisableSteppers();
|
|
|
|
extern block_t *current_block; // A pointer to the block currently being traced
|
|
extern bool x_min_endstop;
|
|
extern bool x_max_endstop;
|
|
extern bool y_min_endstop;
|
|
extern bool y_max_endstop;
|
|
extern volatile long count_position[NUM_AXIS];
|
|
|
|
void quickStop();
|
|
#if defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1
|
|
void digitalPotWrite(int address, int value);
|
|
#endif //defined(DIGIPOTSS_PIN) && DIGIPOTSS_PIN > -1
|
|
void microstep_ms(uint8_t driver, int8_t ms1, int8_t ms2);
|
|
void microstep_mode(uint8_t driver, uint8_t stepping);
|
|
void st_current_init();
|
|
void st_current_set(uint8_t driver, int current);
|
|
void microstep_init();
|
|
void microstep_readings();
|
|
|
|
#ifdef BABYSTEPPING
|
|
void babystep(const uint8_t axis,const bool direction); // perform a short step with a single stepper motor, outside of any convention
|
|
#endif
|
|
|
|
|
|
|
|
#endif
|