130 lines
2.2 KiB
INI
130 lines
2.2 KiB
INI
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PB13
|
|
dir_pin: !PB12
|
|
enable_pin: !PB14
|
|
microsteps: 16
|
|
rotation_distance: 20.30075
|
|
endstop_pin: ^PC0
|
|
position_endstop: 0
|
|
position_max: 594
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 0
|
|
run_current: 0.8
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_y]
|
|
step_pin: PB10
|
|
dir_pin: !PB2
|
|
enable_pin: !PB11
|
|
microsteps: 16
|
|
rotation_distance: 20.29418
|
|
endstop_pin: ^PC1
|
|
position_endstop: 407
|
|
position_max: 407
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 2
|
|
run_current: 0.8
|
|
stealthchop_threshold: 0
|
|
|
|
[homing_override]
|
|
gcode:
|
|
G28 X Y
|
|
|
|
[stepper_z]
|
|
step_pin: PB0
|
|
dir_pin: PC5
|
|
enable_pin: !PB1
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^PC2
|
|
position_endstop: 0.0
|
|
position_max: 250
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PC11
|
|
tx_pin: PC10
|
|
uart_address: 1
|
|
run_current: 0.580
|
|
stealthchop_threshold: 999999
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f103xe_35FFD3054254393930531857-if00
|
|
|
|
[mcu due]
|
|
serial: /dev/serial/by-id/usb-Arduino__www.arduino.cc__Arduino_Due_Prog._Port_857353136323516170E0-if00
|
|
|
|
[output_pin laser_en]
|
|
pin: due:PB25 #D2
|
|
pwm: True
|
|
hardware_pwm: True
|
|
shutdown_value: 0
|
|
|
|
[output_pin laser_pwr]
|
|
pin: due:PC28 #D3
|
|
pwm: True
|
|
hardware_pwm: True
|
|
cycle_time: 0.00006
|
|
shutdown_value: 0
|
|
|
|
[output_pin compressor]
|
|
pin: due:PC22 #D8
|
|
pwm: True
|
|
hardware_pwm: True
|
|
shutdown_value: 0
|
|
|
|
[fan_generic vent]
|
|
pin: due:PC21 #D9
|
|
hardware_pwm: True
|
|
shutdown_speed: 1.0
|
|
|
|
[virtual_sdcard]
|
|
path: ~/.octoprint/uploads/
|
|
|
|
[respond]
|
|
default_type: echo
|
|
|
|
[gcode_macro M3]
|
|
gcode:
|
|
{% set S = params.S|default(0.0)|float %}
|
|
{% if S == 0.0 %}
|
|
SET_PIN PIN=laser_en VALUE=0.0
|
|
{% else %}
|
|
SET_PIN PIN=laser_en VALUE=1.0
|
|
{% endif %}
|
|
SET_PIN PIN=laser_pwr VALUE={S / 255.0}
|
|
|
|
[gcode_macro M4]
|
|
gcode:
|
|
{% set S = params.S|default(0.0)|float %}
|
|
SET_PIN PIN=laser_en VALUE=1.0
|
|
SET_PIN PIN=laser_pwr VALUE={S / 255.0}
|
|
|
|
[gcode_macro M5]
|
|
gcode:
|
|
SET_PIN PIN=laser_en VALUE=0.0
|
|
SET_PIN PIN=laser_pwr VALUE=0.0
|
|
|
|
[gcode_macro M8]
|
|
gcode:
|
|
SET_PIN PIN=compressor VALUE=1.0
|
|
|
|
[gcode_macro M9]
|
|
gcode:
|
|
SET_PIN PIN=compressor VALUE=0.0 |