# Ender 3 S1 Config, Satit Chula Specific

[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA5
position_endstop: 0
position_max: 258
homing_speed: 50

[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA6
position_endstop: 0
position_max: 230
homing_speed: 50

[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC3
microsteps: 16
rotation_distance: 8
endstop_pin: probe:z_virtual_endstop
position_max: 270
position_min: -5

[extruder]
max_extrude_only_distance: 100.0
step_pin: PB4
dir_pin: PB3
enable_pin: !PC3
microsteps: 16
rotation_distance: 7.6190
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC5
control: pid
pid_Kp: 22.865
pid_Ki: 1.292
pid_Kd: 101.178
min_temp: 0
max_temp: 250
pressure_advance = 0.12

[filament_switch_sensor RunoutSensor]
pause_on_runout: False
runout_gcode: PAUSE
insert_gcode: RESUME
switch_pin: !PC15

[heater_bed]
heater_pin: PA7
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PC4
control: pid
pid_Kp: 69.139
pid_Ki: 1.273
pid_Kd: 938.565
min_temp: 0
max_temp: 130


[heater_fan hotend_fan]
pin: PC0
heater: extruder
heater_temp: 50.0

[fan]
pin: PA0

[mcu]
serial: /printerserial
restart_method: command

[printer]
kinematics: cartesian
max_velocity: 500
max_accel: 3000
max_accel_to_decel: 3000
max_z_velocity: 5
square_corner_velocity: 5.0
max_z_accel: 100

[bltouch]
sensor_pin: ^PC14 
control_pin: PC13 
x_offset: -32
y_offset: -41
z_offset: 2.80
speed:10
samples:1
samples_result:average
probe_with_touch_mode: true
stow_on_each_sample: false

[safe_z_home]
home_xy_position: 154,154
speed: 100
z_hop: 10
z_hop_speed: 5

[bed_mesh]
speed: 100
mesh_min: 10, 10
mesh_max: 225, 189
algorithm: bicubic
probe_count: 5,5

[virtual_sdcard]
path: ~/gcode_files

[display_status]

[pause_resume]

[gcode_macro PAUSE]
description: Pause the actual running print
rename_existing: PAUSE_BASE
# change this if you need more or less extrusion
variable_extrude: 1.0
gcode:
  ##### read E from pause macro #####
  {% set E = printer["gcode_macro PAUSE"].extrude|float %}
  ##### set park positon for x and y #####
  # default is your max posion from your printer.cfg
  {% set x_park = printer.toolhead.axis_maximum.x|float - 5.0 %}
  {% set y_park = printer.toolhead.axis_maximum.y|float - 5.0 %}
  ##### calculate save lift position #####
  {% set max_z = printer.toolhead.axis_maximum.z|float %}
  {% set act_z = printer.toolhead.position.z|float %}
  {% if act_z < (max_z - 2.0) %}
      {% set z_safe = 2.0 %}
  {% else %}
      {% set z_safe = max_z - act_z %}
  {% endif %}
  ##### end of definitions #####
  PAUSE_BASE
  G91
  {% if printer.extruder.can_extrude|lower == 'true' %}
    G1 E-{E} F2100
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}
  {% if "xyz" in printer.toolhead.homed_axes %}
    G1 Z{z_safe} F900
    G90
    G1 X{x_park} Y{y_park} F6000
  {% else %}
    {action_respond_info("Printer not homed")}
  {% endif %} 

[gcode_macro RESUME]
description: Resume the actual running print
rename_existing: RESUME_BASE
gcode:
  ##### read E from pause macro #####
  {% set E = printer["gcode_macro PAUSE"].extrude|float %}
  #### get VELOCITY parameter if specified ####
  {% if 'VELOCITY' in params|upper %}
    {% set get_params = ('VELOCITY=' + params.VELOCITY)  %}
  {%else %}
    {% set get_params = "" %}
  {% endif %}
  ##### end of definitions #####
  {% if printer.extruder.can_extrude|lower == 'true' %}
    G91
    G1 E{E} F2100
  {% else %}
    {action_respond_info("Extruder not hot enough")}
  {% endif %}  
  RESUME_BASE {get_params}

[gcode_macro CANCEL_PRINT]
description: Cancel the actual running print
rename_existing: CANCEL_PRINT_BASE
gcode:
  TURN_OFF_HEATERS
  CANCEL_PRINT_BASE