#include <main.hpp>

RemoteVariable pm25_out = RemoteVariable();
RemoteVariable temp_out = RemoteVariable();
RemoteVariable weather = RemoteVariable();

const char *mode_names[] = {"off", "fan_only", "cool"};
const char *fan_speed_names[] = {"auto", "high", "medium", "low"};

AirConditioner ac = {
    .max_temperature = 30,
    .min_temperature = 15,
    .modes = 3,
    .mode_names = mode_names,
    .fan_speeds = 4,
    .fan_speed_names = fan_speed_names,
    .getInfraredCode = &getInfraredCode};
/***********************************************
 *            End Configuration                *
 ***********************************************/

ESPMegaPRO espmega = ESPMegaPRO();
ISEDisplay iseDisplay = ISEDisplay(&iseDisplayAdapter);

ClimateCard climateCard = ClimateCard(AIR_CONDITIONER_IR_PIN, ac,
                                      AIR_CONDITIONER_SENSOR_TYPE, AIR_CONDITIONER_SENSOR_PIN,
                                      AIR_CONDITIONER_RMT_CHANNEL);

void handleMqttMessage(char *topic, char *payload)
{

}

void sendStopBytes()
{
  Serial.write(0xFF);
  Serial.write(0xFF);
  Serial.write(0xFF);
}

void sendExtStopBytes()
{
  iseDisplayAdapter.write(0xFF);
  iseDisplayAdapter.write(0xFF);
  iseDisplayAdapter.write(0xFF);
}

void setup()
{
  gpio_config_t gpio_2_conf;
  gpio_2_conf.intr_type = GPIO_INTR_DISABLE;
  gpio_2_conf.mode = GPIO_MODE_INPUT;
  gpio_2_conf.pull_up_en = GPIO_PULLUP_ENABLE;
  gpio_config(&gpio_2_conf);
  // If GPIO 2 is pulled low, clear the FRAM then reboot (Reset the device to factory defaults)
  bool clear_fram = !gpio_get_level(GPIO_NUM_2);
  Serial.begin(115200);
  iseDisplayAdapter.begin(ISE_DISPLAY_BAUD_RATE, SERIAL_8N1, ISE_DISPLAY_RX_PIN, ISE_DISPLAY_TX_PIN);
  sendExtStopBytes();
  iseDisplayAdapter.print("rest");
  sendExtStopBytes();
  sendStopBytes();
  Serial.print("rest");
  sendStopBytes();
  Serial.print("boot_state.txt=\"Core Initializing . . .\"");
  sendStopBytes();
  espmega.begin();
  // if (clear_fram)
  // {
  //   Serial.print("boot_state.txt=\"Factory Resetting . . .\"");
  //   sendStopBytes();
  //   for (uint16_t i = 0; i < 32768; i++)
  //   {
  //     espmega.fram.write8(i, 0);
  //   }
  //   esp_restart();
  // }
  Serial.print("boot_state.txt=\"IoT Initializing . . .\"");
  sendStopBytes();
  espmega.enableIotModule();
  ETH.begin();
  espmega.iot->bindEthernetInterface(&ETH);
  Serial.print("boot_state.txt=\"Network Initializing . . .\"");
  sendStopBytes();
  espmega.iot->loadNetworkConfig();
  espmega.iot->connectNetwork();
  Serial.print("boot_state.txt=\"MQTT Initializing . . .\"");
  sendStopBytes();
  espmega.iot->loadMqttConfig();
  espmega.iot->connectToMqtt();
  Serial.print("boot_state.txt=\"Display Initializing . . .\"");
  espmega.enableInternalDisplay(&Serial);
  espmega.enableWebServer(80);
  espmega.inputs.registerCallback(on_pin_change);
  espmega.outputs.setAutoSaveToFRAM(true);
  espmega.installCard(2, &climateCard);
  climateCard.bindFRAM(&espmega.fram, 5000);
  climateCard.loadStateFromFRAM();
  climateCard.setFRAMAutoSave(true);
  espmega.display->bindClimateCard(&climateCard);
  espmega.iot->registerCard(0); // Register the Input Card
  espmega.iot->registerCard(1); // Register the Output Card
  espmega.iot->registerCard(2); // Register the Climate Card
  auto bindedGetTime = std::bind(&ESPMegaPRO::getTime, &espmega);
  iseDisplay.begin(&espmega.inputs, &espmega.outputs, &climateCard);
  espmega.iot->registerRelativeMqttCallback(&handleMqttMessage);
  iseDisplay.registerPageChangeCallback(&handlePageChange);
  // placeholder
  // PM2.5 PPM Remote Variable
  // 12 bytes remote variable, 11 characters + null terminator
  // Enable value request at /iqair/pm25_request
  pm25_out.begin(6, "/aqi/value", espmega.iot, true, "/aqi/value_request");
  // Temperature Remote Variable
  temp_out.begin(6, "/temp/value", espmega.iot, true, "/weather/temp_request");
  // Weather Remote Variable
  weather.begin(45, "/weather", espmega.iot, true, "/weather_request");
}

void loop()
{
  espmega.loop();
  iseDisplay.loop();

  // Update the time every 15 seconds
  //static bool run_when_init = false; // No static ? , this shit will reset to 0 every loop
  static uint32_t last_time_updated = 0;
  //rtctime_t time = espmega.getTime(); 
  //when init update once then update every 15 seconds
  // You don't need this, when it go from page 0 to 1 it call handlePageChange
  // if(!run_when_init){
  //   time = espmega.getTime();
  //   iseDisplay.updateDateTimeText(time);
  //   last_time_updated = millis();    
  //   run_when_init = true;
  // }
  
  
  if (millis() - last_time_updated > 15000)
  {
    rtctime_t time = espmega.getTime();
    // log time
    ESP_LOGI("time", "Time: %d:%d:%d", time.hours, time.minutes, time.seconds);
    ESP_LOGI("Date", "Date: %d/%d/%d", time.day, time.month, time.year);
    iseDisplay.updateDateTimeText(time);
    last_time_updated = millis();
  }
  // Update the PM2.5 PPM value every 5 minutes
  // static uint32_t last_pm25_out_update = 0;
  // if (millis() - last_pm25_out_update > 300000)
  // {
  //   uint16_t pm25_out_value = get_pm25_out();
  //   iseDisplay.updatePMoutside(pm25_out_value);
  //   last_pm25_out_update = millis();
  // }
  // // Update the temperature value every 5 minutes
  // static uint32_t last_temp_out_update = 0;
  // if (millis() - last_temp_out_update > 300000)
  // {
  //   float temp_out_value = get_temp_out();
  //   iseDisplay.updateTempOutside(temp_out_value);
  //   last_temp_out_update = millis();
  // }
  // // Update the weather value every 5 minutes
  // static uint32_t last_weather_update = 0;
  // if (millis() - last_weather_update > 300000)
  // {
  //   char *weather_value = weather.getValue();
  //   iseDisplay.updateWeather(weather_value);
  //   last_weather_update = millis();
  // }

}

void on_pin_change(uint8_t pin, uint8_t value)
{

}

// uint16_t get_pm25_out()
// {
//   uint16_t pm25_out_value = 0;
//   // Read PM2.5 PPM from sensor
//   pm25_out_value = atoi(pm25_out.getValue());
//   return pm25_out_value;
// }
// float get_temp_out()
// {
//   float temp_out_value = 0;
//   // Read temperature from sensor
//   temp_out_value = atof(temp_out.getValue());
//   return temp_out_value;
// }

void handlePageChange(uint8_t page) {

  // Which already send the time
  //printESP_LOGI the page have changed
  ESP_LOGI("Page", "Page change to: %d", page);
  rtctime_t time = espmega.getTime();
  iseDisplay.updateDateTimeText(time);
  iseDisplay.updateLightGroupStatePageDashboard();
  //iseDisplay.updatePMinside();
  /* iseDisplay.updatePMoutside(get_pm25_out());
  iseDisplay.updateWeather(weather.getValue());
  iseDisplay.updateTempOutside(get_temp_out()); */
  /* iseDisplay.updateACState();
  iseDisplay.updateAirPurifierState();
  iseDisplay.updateLightGroupStatePageStandby();
  iseDisplay.updateLightGroupStatePageDashboard();
  iseDisplay.updateuserACmode();
  iseDisplay.updateAirPurifierStateStandby(); */
}